G.M. International DIN RAIL mounting Intrinsically Safe Galvanic Isolators and Repeaters. The D Range provides the most simple and cost effective means of implementing Intrinsic Safety into your Hazardous Areas/Locations applications.

D1000 Series I S Barrier Overview, pdf (544kb)

The D1014S and D1014D is a single and dual channel DIN Rail Repeater Power Supply requiring SIL 2 level (according to EN61508) in safety related system for high risk industries. Provides a fully floating dc supply for energizing conventional 2-wire 4-20 mA Transmitter or 3 / 4 Wire 4-20mA signals located in Hazardous Area, and repeats the current in floating circuit to drive a Safe Area load.

D1010 Tx Repeater Power Supply, pdf (192kb)

The single and dual channel DIN Rail Repeater Power Supply, D1014S and D1014D is a high integrity analog input interface suitable for application requiring SIL 2 level (according to EN61508) in safety related system for high risk industries. Provides a fully floating dc supply for energizing conventional 2-wire 4-20 mA Transmitters located in Hazardous Area, and repeats the current in floating circuit to drive a Safe Area load.

D1014 Tx Repeater Power Supply, pdf (80kb)

The D1043 series are quad channel Din Rail Digital Output Modules enabling a Safe Area contact, logic level or drive signal, to control a Solenoid, Audible Alarm, or LED’s in Hazardous Area, providing 3 port isolation (input/output/supply).

D1043 SIL3 Solenoid Driver, pdf (692kb)

Klay Instruments offers a wide range of ‘All Stainless’ Level Switches mainly for use in the Food and Pharmaceutical industry and water and waste water industry. The Vibra-Switch levelswitch are available in 2 executions.

The ‘C’ version is the compact level switch with a connector or cable connection and the ‘S’ version is equipped with a complete stainless steel electronics housing.

The ‘FLX’ levelswitch is based on the principle of conductivity and is a very rugged designed stainless steel levelswitch.  All standard process connections like G1 thread, milkcoupling, Tri-Clamp and Flanges are available.

		D2000 Intrinsically Safe Multiplexer, pdf (1,5Mb)
		D2010M Temperature, pdf (840kb)

The DTM 8000 is a Continuous Smart Digital Alarm Monitor System used for the reliable and effective monitoring of up to 48 channels of process variables.

The system is not a multiplexing type machine, but a continuous one, which means there is no delay in monitoring the variables, because each input signal is continuously monitored in a parallel operating mode.

For this unique feature the unit is suitable to monitor critical rotating machines like Turbines and Compressors, (for instance: Bearing Temperature) where a few millisecond delay in alarming and shutting down could result in a disaster for the entire machine and plant operation.

DTM8000 Digital Alarm Monitor System, pdf (680kb)

The PSD1000 is a DIN Rail mounting universal AC input switching power supply with 24 Vdc 500 mA current output capability, to supply D1000 Series units or other 24 Vdc devices; it provides isolation between input and output and a relay for detection of supply fault (input line, output overload or thermal overload). The output is protected from overload (current or thermal) and short circuit (the unit switches the output off for a second and then tries to re-activate it until the fault condition is removed).

The output is diode protected to connect multiple power supply (redundant output) or to increase the output power.

		PSD1000, pdf (48kb)
		PSD1206 Zone 2 PSU, pdf (128kb)
		PSD1210 SIL 2 Zone 2 PSU, pdf (128kb)

Understanding ATEX Hazardous Area Definitions

Understanding Safety Integrity Levels (SIL) Definitions

		Wall Poster-ATEX Definitions, pdf (144kb)
		Wall Poster-SIL Definitions, pdf (216kb)